Purpose and Essential Duties

The Pipe Welder will perform welding procedures according to code based on the project needs and specifications.

• Perform welding tasks at a level that meets job specifications.
• Mark the welds made as directed by company policy.
• Clean and paint all welds as required by the job specifications.
• Assist Fitter as needed.
• Complete and maintain a weld map if required.

This position is Full Time, Non-Exempt, and reports to the Pipefitter Foreman.

Required Education, Experience, and Qualifications :

• Must be able to pass a 6G SMAW & GMAW X-ray test.
• Must be able to weld 30in bore pipe.
• Minimum 2 years of experience in commercial mechanical piping.
• Basic OSHA 10 hour safety.
• Operate an oxygen and acetylene burning rig, cutting and beveling pipe.
• Ability to work overtime when required.

Travel Requirements

Infrequent travel to Company or client locations. Approximately 10% of time will be spent traveling.

Physical / Work Environment Requirements

Essential

Must be able to lift heavy objects up to 50lbs, be able to bend / stoop, squat / crouch, climb, kneel and twist. Must be able to climb ladders, work both inside and outside, and around moving equipment safely.

Bernhard is proud to be an

The overall objective of this position is to align, fit, and weld fabricated sheet metal parts of our products per drawing specifications, and insure accuracy and compliance with quality standards.

Apply technical knowledge to review engineering drawings and determine requirements and specifications needed for the fabrication of sheet metal structures of our product.

Follow blueprints and layout specifications to position, align and fit parts for quality and efficient welding

Set up welding machines with the proper wire speed to produce a quality weld for different materials and thicknesses.

Weld in flat, horizontal, vertical and overhead positions and then examine the welds for quality specifications, including proper bead sizes.

Clean welds using hand scrappers, grinders and sanders as required to prepare surfaces for painting.

Proficiently operate a cutting torch, bank saw, ironworker, grinder and other fabrication equipment.

Maintain a safe, clean well organized work area.

Manually apply a filler rod to weld stainless and aluminum.

Clean stainless and aluminum weld joints using wire brush portable grinders or chemical baths.

Ensure quality and efficiency by completing the job task faster than estimated hours.

Serve as a mentor by coaching 2nd and 3rd Class Welders

Required Skills

Knowledge of raw materials, production processes, quality control and other techniques for maximizing the effective manufacture and distribution of good.

Knowledge of machines and tools, including their designs, uses, repair and maintenance.

Ability to read and process drawings and cut-sheet packages. Proficient in measuring, squaring and math skills. Ability to MIG or Flux-Core weld.

The ability to keep your hand and arm steady while moving your arm to while holding you arm and hand in one position.

The ability to quickly move your hand, your hand together with your arm or your two hands to grasp, manipulate or assemble object.

Required Experience

High school diploma / GED required

Heli-arc certification required

5 years of experience in sheet-metal fabrication or welding

Knowledge of raw materials, production processes, quality control and other techniques for maximizing the effective manufacture and distribution of good.

Knowledge of machines and tools, including their designs, uses, repair and maintenance.

Ability to read and process drawings and cut-sheet packages. Proficient in measuring, squaring and math skills. Ability to MIG or Flux-Core weld.

The ability to keep your hand and arm steady while moving your arm to while holding you arm and hand in one position.

The ability to quickly move your hand, your hand together with your arm or your two hands to grasp, manipulate or assemble object.

In this job, you will :

All job duties may or may not be performed by all job incumbents, may vary dependent on assigned department.

• Inspect, measure, adjust and test completed metal work pieces to ensure conformance to specifications.
• Read blueprints, work orders or production schedules to determine product or job instructions or specifications.
• Assemble, align and clamp work pieces into holding fixtures to bond, heat-treat, or solder fabricated metal components.
• Set up, operate, and maintain welding machines / equipment that join or bond components to fabricate metal products or assemblies.
• Heat and grind metal parts and components using hand tools, torch, or other welding equipment.
• Fabricate and fit substrates as required.
• Monitor the welding, burning and fitting process to ensure parts are not overheated or damaged.
• Maintain a safe and clean work environment by complying with all safety procedures, rules and regulations.
• Other duties as assigned.

Here's what you'll need to be considered :

Education

Required High School Diploma or equivalent

Preferred

Experience

Required

Knowledge, Skills, and Abilities

• Intermediate to advanced level of understanding of mechanical maintenance, knowledge of machines and tools, including the designs, uses, repair and maintenance.
• General knowledge of many types of tools.
• Effective interpersonal, oral and written communication skills with the ability to interact with all levels of people within and outside the organization.
• Basic mathematical skills, i.e., add subtract, multiply and divide.
• Ability to read and understand measurements.
• Ability to follow direction and to use logical thought process to interpret oral and written instructions and recommend alternative solutions to mechanical problems.
• Ability to complete documentation requirements.
• Ability to work well both independently and as part of a team.
• Ability to use tools appropriate for assigned task.
• Ability to remain focused on exceptional customer service, both internally and externally.

Here's additional information you need to know :

Physical Demands & Requirements

• Ability to lift / push / pull 50 lbs.
• Ability to climb, crawl, stoop, kneel and squat occasionally.
• Ability to use manual dexterity (i.e., grasp, manipulate and assemble small objects).
• Arm / hand steadiness and multi-limb coordination.
• Ability to climb stairs and climb ladders to significant heights.
• Ability to work around water.
• Ability to grasp and reach frequently.
• Ability to understand and communicate verbally, in person and over two-way radio.
• Ability to work outside in extreme weather conditions.
• Ability to perform work in confined spaces.
• Ability to work in an environment with high dust levels around grain and other bulk products.
• Ability to meet requirement of and utilize all applicable PPE, when applicable.
• Uses near, far and peripheral vision and depth perception for task(s) being performed.

Hearing. Perceiving the nature of sounds at normal speaking levels with or without correction. Ability to receive detailed information through oral communication, and to make the discriminations in sound.

The employee is required to have close visual acuity to perform an activity such as : preparing and analyzing data and figures;

transcribing; viewing a computer terminal; extensive reading.

Environmental Conditions

The work environment described here are meant to be representative of those an employee would normally encounter while performing the essential functions of this job.

The physical environment requires the employee to work both inside and outside in heat / cold, wet / humid, and dry / arid conditions.

Frequently required to use personal protective equipment.

Travel, 5%-20% travel may be required at some facilities. This may include off-site training and / or work at alternate locations.

Are you ready to make a meaningful career move & an impact at Cooper Consolidated, LLC? Apply today!

Known in our industry for stability and high ethics, Cooper Consolidated, LLC offers a stellar benefits package including : an outstanding 401(k) retirement plan with company contributions, medical, prescription drug, dental, vision, life, & disability benefits, flexible spending accounts, paid leave (holidays, vacation, sick), wellness programs, recognition programs, community involvement opportunities, and much more!

Cooper Consolidated, LLC is an Equal Opportunity Employer. EEO is the Law links in or .

The above is intended to describe the general content of and requirements for the performance of this position. It should not be construed as a detailed description of all the work requirements that may be performed in the job.

All Third Party Agencies, Headhunters, and Recruiters

Cooper Consolidated, LLC and its Subsidiaries only forms contracts with recruiters with whom we have an established relationship and with whom we have in place a signed contract.

All contact from third parties must go through our Human Resources Department. Any contact made outside of our Human Resources Department by a third party will cancel any future business relationships between the third party and Cooper Consolidated, LLC and its Subsidiaries.

Company Overview

For over 35 years, Himmel’s Architectural Door and Hardware has provided quality products and services in the commercial door and architectural specialties industry.

Himmel’s is a growing organization with locations in New Orleans, Prairieville, Nashville and Houston. We pride ourselves as the door opening experts, not simply a construction material supplier.

Our family owned and operated company is currently seeking a Welder to join our team!

The Fabrication Team customizes door frames to meet the needs of our commercial customers. This position is scheduled Monday -Friday 7am 3 : 30pm.

Job Responsibilities

• Selects appropriate material for each job based on the desired or necessary strength.
• Preps door frames for various hardware items using templates.
• Measures, cuts, and welds pieces together according to specifications, blueprints, or directions.
• Connects pieces or secures seams by welding.
• Uses appropriate machinery to complete assigned jobs.
• Maintains clean and orderly workspace.
• Performs other related duties as assigned.

Required Skills

• Ability to complete projects with accuracy and precision.
• Ability to safely use machinery and tools involved in fabrication work.
• Ability to follow directions.
• Ability to read templates and schematics to understand product assignment.
• High School diploma

Physical Requirements

• Prolonged periods lifting, reaching, bending and standing.
• Must be able to lift 75 pounds at times.

Benefits

• Competitive compensation and bonuses
• Medical, Dental and Vision Insurance
• Company paid life insurance and Long-Term Disability
• 3 Weeks of Paid Time Off and Paid Holidays
• Supplemental / Voluntary Insurance Life, Accident, Critical Illness, Short-Term Disability,
• Advancement Opportunity to grow your career

Job Type : Full-time

Salary : From $18.00 per hour

Weekly day range :

Monday to Friday

Ability to commute / relocate :

Reliably commute or planning to relocate before starting work (Required)

Experience :

Welding : 1 year (Preferred)

Work Location : In person

Candidates should possess demonstrable skill and experience with the following :

• MIG, Flux Core, and Stick Aluminum, Carbon Steel and Stainless Steel.
• Must understand heat requirements, amperages, voltages, pre-heats, inter-pass temperatures and post head requirements.
• Able to layout, burn, and prepare plate for installation.
• Familiar with filler wire controls, filler wire selection and acceptable weld preparation techniques.
• Have working knowledge of weld procedural requirements, special requirements and safety requirements for the accomplishment of tasks.
• Able to perform grinding and joint preparation for NDE and inspection process and be proficient in carbon arc gouging.

Get job alerts by email. Sign up now!